银河集团www.198.net|中國·BinG百科 NO.1

银河集团:198net

产品中心Product Center

SFP+/10G-AOC-X 1m

Whandar\'s SFP+ Active Optical Cable (AOC) is a 10Gbps solution to10G Ethernet, and datacenter. The integrated cable transmits 10Gbps data in each direction over MMF with distance up to 100m. The AOC is SFP+ MSA compliance, low power consumption and lightweigh...

全国咨询热线:

0755-86654236 /

联系我们 在线客服

扫一扫关注我们扫一扫关注我们

产品详情

产品介绍

1. Applications

Ø  Datacom

Ø  10G Ethernet

Ø  Other high-throughput data transmission network

2. Features

 

Ø  10Gb/s active optical cable up to 100m OM2 MMF

Ø  850nm VCSEL and PIN receiver

Ø  Single 3.3V power supply

Ø  Operating Case Temperature: -5~75

Ø  Hot pluggable

Ø  Low Power Consumption

Ø  Light weight

Ø  Small Bend Radius

Ø  Digital Diagnostic Monitor(DDM)

Ø  All-metal Housing for Superior EMI Performance

3. Description

   Whandar's SFP+ Active Optical Cable (AOC) is a 10Gbps solution to10G Ethernet, and datacenter. The integrated cable transmits 10Gbps data in each direction over MMF with distance up to 100m. The AOC is SFP+ MSA compliance, low power consumption and lightweight.

4. standard

Ø  Compliant with SFF-8431 and SFF-8432

Ø  Compliant with SFF-8472 Rev 10.2

Ø  Compliant with IEEE 802.3ae 10GBASE-LR and 10GBASE-LW

Ø  RoHS Compliant

 

5. Performance Specifications

5.1. Absolute Maximum Ratings

These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.

Table.1 Absolute maximum ratings

Parameter

Symbol

Min

Max

Units

Storage temperature

Ts

-20

85

Relative Humidity

RH

5

85

%

Supply Voltage

Vc

-0.3

3.6

V

Supply Current

Icc


450

mA

 

5.2. Recommended Operating Conditions

Table.2 Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Operating Case Temperature

Standard Tc

0

25

70

°C

Power Supply Voltage

Vcc

3.13

3.3

3.47

V

Power Supply Current

Icc


60

260

mA

Power Dissipation

PD


600

800

mW

Data Rate

DR


10.3125


Gbps

Transmission Distance

TD



100

m

5.3. Transmitter Specification

Table.3 Transmitter Specification (Optical)

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Average Output Power

Po

-5


-1

dBm


Disable Power

Poff



-40

dBm


Extinction Ratio

ER

3.5



dB


Output Centre Wavelength

λc

840


860

nm


 

Table.4 Transmitter Specification (Electrical)

Parameter

Symbol

Min

Typical

Max

Unit

Data Input Swing Differential

VIN

200


700

mV

Input Differential Impedance

ZIN

90

100

110

Ω

Transmit Disable Input

High

VIH

2.0


Vcc+0.3

V

Low

VIL

0


0.8

V

 

5.4. Receiver Specification

Table.5 Receiver Specification (Optical)

Parameter

Symbol

Min

Typical

Max

Unit

note

Centre Wavelength

λc

840

850

860

nm


Receiver Sensitivity

Sen



-11

dBm

1

Receiver Overload

Psat

0.5



dBm

1

LOS De-Assert

LOSD



-15

dBm


LOS Assert

LOSA

-30



dBm


LOS Hysteresis


0.5


4

dB


Receiver Reflectance

Rrx



-12

dB


Note :1. Measured at BER 10-12, 10.3Gbps, PRBS2^31-1, NRZ

 

Table.6 Receiver Specification (Electrical)

Parameter

Symbol

Min

Typical

Max

Unit

note

Data Output Swing Differential

Vout

300


800

mV


Rx-Los Fault

Vlf

2.0


VccHOST

V


Rx-Los Normal

Vln

0


0+0.8

V


Output rise and fall time

Tr, Tf

28



ps


 

5.5. Diagnostics Specification

 

Table.7Diagnostics Specification

Parameter

Range

Unit

Accuracy

Calibration

Temperature

0 to 70

±3℃

Internal / External

Voltage

3.0 to 3.6

V

±3%

Internal / External

Bias Current

0 to 100

mA

±10%

Internal / External

TX Power

-5 to-1

dBm

±3dB

Internal / External

RX Power

-30to 0

dBm

±3dB

Internal / External

 

5.6. Pin Definitions

图片5.png图片4.png

Table.8Pin Definitions

PIN

Symbol

Description

Remarks

1

VEET

Transmitter ground (common with receiver ground)

Circuit ground is isolatedfrom chassis ground

2

Tx_Fault

Transmitter Fault. Not supported


3

Tx_Disable

Transmitter Disable. Laseroutput disable on high or open

Disabled: TDIS>2V or open

Enabled: TDIS<0.8V

4

SDA

2-wire Serial Interface Data Line

Should Be pulled up with4.7k – 10kohm on hostboard to a voltage between2V and 3.6V

5

SCL

2-wire Serial Interface Clock Line

6

MOD_ABS

Module Absent. Grounded within the module.

7

RS0

No connection required


8

RX_LOS

Loss of Signal indication. Logic 0 indicates normal operation

LOS is open collector output

9

RS1

No connection required


10

VEER

Receiver ground (common with transmitter ground)

Circuit ground is isolatedfrom chassis ground

11

VEER

Receiver ground (common with transmitter ground)

12

RD–

Receiver Inverted DATA out. AC coupled


13

RD+

Receiver Non-inverted DATA out. AC coupled


14

VEER

Receiver ground (common with transmitter ground)

Circuit ground is isolatedfrom chassis ground

15

VCCR

Receiver power supply


16

VCCT

Transmitter power supply


17

VEET

Transmitter ground (common with receiver ground)

Circuit ground is isolatedfrom chassis ground

18

TD+

Transmitter Non-Inverted DATA in. AC coupled


19

TD–

Transmitter Inverted DATA in. AC coupled


20

VEET

Transmitter ground (common with receiver ground)

Circuit ground is isolatedfrom chassis ground

 

5.9. Mechanical Dimensions

图片6.png

Diagram of Mechanical Dimensions

6. Application Cautions

6.1. ESD

This transceiver is specified as ESD threshold 1kV for high speed pins and 2kV for all other electrical input pins, tested per MIL-STD-883, Method 3015.4 /JESD22-A114-A (HBM).  However, normal ESD precautions are still required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment.

6.2. LASER SAFTY

This is a Class 1 Laser Product according to IEC 60825-1:1993:+A1:1997+A2:2001.  This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated (July 26, 2001)

7. Order Information

Part No.

Description

Rate

Length

Optical Mode

HD-SFP+/10G-AOC-1

10G SFP+ to 10G SFP+ AOC

10.3G

1 meter

OM2

HD-SFP+/10G-AOC-2

10G SFP+ to 10G SFP+ AOC

10.3G

2 meters

OM2

HD-SFP+/10G-AOC-3

10G SFP+ to 10G SFP+ AOC

10.3G

3 meters

OM2

HD-SFP+/10G-AOC-5

10G SFP+ to 10G SFP+ AOC

10.3G

5 meters

OM2

HD-SFP+/10G-AOC-7

10G SFP+ to 10G SFP+ AOC

10.3G

7 meters

OM2




菜单产品中心Product center